Plumbing Essentials: An Essential for Installing a Bathtub
Plumbing Essentials: An Essential for Installing a Bathtub
Blog Article
This article below on the subject of A Step-by-Step Guide to Installing a Bathtub is really fascinating. You should investigate it.

Installing a bath tub isn't precisely brain surgery, however it does require solid plumbing, carpentry, and sometimes, tiling abilities. Changing an old tub with a new one is also a reasonably tough project. If the old tub is conveniently easily accessible, the job can relocate rapidly; if you have to open up a wall to eliminate the old tub as well as position the brand-new bathtub, the task is a lot harder. In either case, the project is within a house handyman's skills, although you will require an assistant to move out the old bathtub and also set in the new one. Ensure you have certified on your own for the job and also are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed job, it is better to take into consideration utilizing one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This short article will certainly aid you mount a brand-new bath tub in your shower room if you have actually already purchased a new tub as well as don't require to transform the plan of your previous water supply pipelines.
Your devices and product checklist need to make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, turn on the faucets to drain any water staying in the system. The procedure of removing the existing taps can be quite troublesome as a result of the restricted gain access to that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel ready for the staying water that will come from the pipelines. As soon as the supply pipes have actually been eliminated, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from transforming during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to going on to fit the new faucets, compare the pipeline links on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will need lowering couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the installing opening in the bath/basin making certain that the washers remain in area between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. Once the tap is securely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous type needs to be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be attached to the other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bathtub
Making use of both wood boards under its feet, put the tub in the needed placement. The wooden boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level as well as adjusting the feet on the tub up until the level reads degree.
To mount faucets, fit the bottom of the furthest versatile faucet port to the suitable supply pipe by making a compression join; after that do the exact same for the other faucet.
Activate the water system and inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the tub and also inspect the overflow electrical outlet and also the normal outlet for leaks.
Finally, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also securing around the tub needs to wait up until the bath tub has been made use of a minimum of when as this will certainly resolve it into its last placement.
Preparing for the Installation
First of all, the supporting structure supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to stop pressure on the bathtub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make certain you utilize all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently be ready to be suited its final position.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bath as well as the tiling, leading to complications with moisture as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, and also can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly fill the bath tub with water before sealing, to permit the activity experienced when the bathtub remains in use. The sealant can split relatively early if you do not consider this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also easily readily available on the marketplace. It is advisable to fit the floor tiles using waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

As a serious reader about A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that blog post was sensible. For those who enjoyed our blog post please remember to pass it around. Thank-you for your time invested reading it.
Immediate support available. Report this page